Brushhollow Shaker: Construction & Specs

How every Brushhollow cabinet is built. Sizes, door counts and shelf counts for each cabinet are on its product page.

3/4" Baltic birch plywood box with a 1/4" birch plywood back
Solid poplar face frame, 1.5" rails and stiles
Shaker 5-piece doors, 2.25" stiles and rails, 1/2" overlay; 0° and 15° profiles
Shaker drawer fronts with 2 1/4" stiles and 1 1/4" rails; 5" top drawer front
1/2" Baltic birch drawer boxes with removable plywood bottoms
Rough-sanded flat to 120 grit with major blemishes filled. You finish-sand before priming and painting.
Hinges and drawer slides per selected option

Cabinet box

Box	3/4" Baltic birch plywood
Back	1/4" birch plywood (5.2mm actual), set in 1/4" wide, 3/8" deep dados 3/4" in from the rear edge of both sides and the bottom, running full height to the top of the box; rear nailers sit behind the back.
Assembly	Tops and bottoms secured with pocket holes
Rear nailers	Two (upper and lower), 3" minimum
Interior	Factory sanded
Shelves	3/4" Baltic birch plywood, edge-banded, set back 1"
Shelf-pin holes	1.25" spacing, starting 6.25" from the bottom and ending about 6.25" from the top (none on drawer banks)

Material	Solid poplar face frame
Rails and stiles	1.5" wide
Mounting	Flush with the inside cabinet wall, with a 25/32" overhang on the outside with 18mm sides (your installer can trim where cabinets meet, if desired)

Door style	Shaker 5-piece door, about 3/4" thick
Door stiles and rails	2.25" wide
Drawer fronts	Shaker drawer fronts: 2 1/4" stiles and 1 1/4" rails (larger center panel)
Shaker profile	Offered in both 0° and 15° shaker profiles (slab fronts have no profile option)
Center panels	MDF: 1/4" flat panel (5.6mm actual, in a 1/4" groove) or 3/4" raised panel; glass-ready doors also offered (glass not included)
Overlay	1/2" overlay, 1/8" gap between doors
Top drawer front	5" tall on all base cabinets (including blind corners) and drawer banks; 3" inside height
Slab drawer-bank fronts	Poplar
Hinges	Per selected option

Drawer boxes	1/2" Baltic birch (12mm actual), glued and stapled butt joints
Drawer bottoms	1/4" sanded plywood (birch, maple or similar) in a 1/4" groove 1/2" up (undermount recess); open back lets the bottom be removed (staples must be removed first)
Drawer box width	Face frame opening minus 5/8" (undermount slides)
Drawer box height	Every drawer box is 2" shorter inside than its front
Top drawer inside height	3"
Drawer bank face frame	30.5" tall with 1.5" rails between drawers; fronts at 1" total overlay
3-drawer bank fronts	5", 11 1/4", 11 1/4" (top to bottom)
4-drawer bank fronts	5", 6 3/4", 7 1/4", 8" (top to bottom)
3-drawer bank inside heights	3", 9 1/4", 9 1/4" (top to bottom)
4-drawer bank inside heights	3", 4 3/4", 5 1/4", 6" (top to bottom)
Slab drawer banks	Same front sizes and drawer inside heights as Shaker
Drawer slides	Undermount only: contractor-grade or luxury soft-close, per selected option

Height	34.5", designed for a 1.5" countertop
Depth	24" to the front of the face frame
Box	Sides 23-1/4" deep; full-depth bottom; 3/4" face frame brings overall depth to 24".
Toe kick	4" high, 3.5" deep
Standard base door	23" tall, below a 5" drawer front; 12"–24" have one door, and you choose the hinge side, left or right, at no extra cost
Top stretchers	Two, front and back, 3" wide; cut for sink installs
Shelves	1 adjustable shelf (sink bases and drawer banks have none)
Blind corner base	Blind panel with one shelf; door hinged on the blind side (blind left = hinges left, blind right = hinges right), so it opens away from the blind panel toward the usable opening
Sink base	5" false front instead of a drawer; it matches the drawer fronts and has no knob or pull. Installer cuts through the 1/4" back for plumbing

Depth	12" to the front of the face frame
Heights	30", 36" and 42"
Widths	12", 15", 18", 21", 24", 27", 30", 33", 36"
Doors	12"–21" one door; 24" one or two doors; 27"–36" two doors. Single-door units (12"–21", and 24" with one door): you choose the hinge side, left or right, at no extra cost
Shelves	2 to 3 adjustable shelves, depending on height

Surface	Rough-sanded flat to 120 grit with major blemishes filled. You finish-sand before priming and painting.
Finish	Ships unfinished
Lead time	6 weeks

Specifications as of October 2026 and subject to change. Hinge and drawer-slide hardware depends on the option you choose.